Page Length: 46

Size: 1673 KB

Format: PDF & Word

5,000.00

Abstract
Biodiesel is a renewable fuel that will soon be fully accepted in the commercial world
but there are limitations to its use that need improvement. The use of oxygenated
additives have improved the burning/fuel qualities of conventional diesel and gasoline.
These oxygenates may also improve the qualities of biodiesel. This paper focuses on
comparing the fuel qualities such as the density, specific gravity, heat content, flash
point, and kinematic viscosity of oxygenate-biodiesel blends. The biodiesel was
produced from fresh and waste cooking oil and they were characterized and compared to
ASTM standards. The oxygenated additives (ethanol, methanol and diethyl ether) were
blended in the percentages 10, 20, 30 and 40% with biodiesel from fresh and waste oil.
The physicochemical properties such as kinematic viscosity, density, specific gravity,
flash point and heat content were analyzed for the blends. The density and specific
gravity values were within the range of 0.74-0.84 g/ml and 0.76-0.85 respectively. The
kinematic viscosities at 40oC were within 3.5-5.0 mm2
s
-1
after oxygenated additives
were added. The blends ignited at 16oC before the flash points could be gotten. The heat
content values for the biodiesel from fresh oil increased at 10 and 20% but decreased at
40% while that of biodiesel from waste oil decreased at 10, 30, and 40% for the ethanol
and methanol blends. The diethyl ether blend did not show any pattern with increase in
addition. The oxygenate addition improved the density, specific gravity, and kinematic
viscosity. Oxygenate addition may be a good way of improving the properties of
biodiesel as shown in the project.
ii
Table of Contents
Abstract …………………………………………………………………………………………………………………………..i
LIST OF TABLES ………………………………………………………………………………………………………….iv
LIST OF FIGURES ………………………………………………………………………………………………………… v
LIST OF EQUATIONS ………………………………………………………………………………………………….vii
Acknowledgements…………………………………………………………………………………………………………ix
CHAPTER 1: Introduction………………………………………………………………………………………….. 1
1.1 Biodiesel…………………………………………………………………………………………………………. 1
1.2 Advantages of biodiesel……………………………………………………………………………………. 2
1.3 Biodiesel production………………………………………………………………………………………… 3
1.4 Waste vegetable oil as feed stock………………………………………………………………………. 4
1.5 Limitations of Biodiesel…………………………………………………………………………………….. 5
1.6 Aims, Objectives and Significance………………………………………………………………………. 5
CHAPTER 2: Literature Review …………………………………………………………………………………. 6
2.1 Emissions characteristics ………………………………………………………………………………….. 6
2.2 Flash point………………………………………………………………………………………………………. 8
2.3 Density …………………………………………………………………………………………………………… 9
2.4 Energy content………………………………………………………………………………………………. 10
2.5 Viscosity ……………………………………………………………………………………………………….. 11
2.6 Pour point and cloud point……………………………………………………………………………… 12
CHAPTER 3: Materials and Methods…………………………………………………………………………. 14
3.1 Materials………………………………………………………………………………………………………. 14
3.2 Characterization of the fresh and waste cooking oil …………………………………………… 14
3.2.1 Free fatty acid content…………………………………………………………………………….. 14
3.2.2 Moisture content ……………………………………………………………………………………. 15
3.2.3 Specific gravity ……………………………………………………………………………………….. 15
iii
3.2.4 Heat content ………………………………………………………………………………………….. 15
3.2.5 Viscosity ………………………………………………………………………………………………… 15
3.2.6 Ash content……………………………………………………………………………………………. 16
3.2.7 Density: …………………………………………………………………………………………………. 16
3.2.8 Pour point and cloud point ………………………………………………………………………. 16
3.3 Biodiesel production………………………………………………………………………………………. 17
3.3.1 Esterification ………………………………………………………………………………………….. 17
3.3.2 Trans esterification …………………………………………………………………………………. 17
3.4 Characterization of the biodiesel from fresh and waste cooking oil……………………… 18
3.4.1 Flash point……………………………………………………………………………………………… 18
3.5 GC-MS and Infrared spectroscopy of the oil samples and biodiesel ……………………… 18
3.5.1 GC-MS …………………………………………………………………………………………………… 18
3.5.2 Infrared spectroscopy ……………………………………………………………………………… 19
3.6 Blending of the biodiesel with the oxygenates…………………………………………………… 19
CHAPTER 4: Results and discussion …………………………………………………………………………. 20
4.1 Percentage yield…………………………………………………………………………………………….. 20
4.2 Confirmation of biodiesel produced using GC-MS and IR ……………………………………. 20
4.3 Characteristics of the biodiesel produced …………………………………………………………. 22
4.4 Density …………………………………………………………………………………………………………. 24
4.5 Viscosity ……………………………………………………………………………………………………….. 27
4.6 Flash point…………………………………………………………………………………………………….. 30
4.7 Heat content …………………………………………………………………………………………………. 31
CHAPTER 5: Summary and Conclusion…………………………………………………………………….. 33
References……………………………………………………………………………………………………………………. 34
iv
LIST OF TABLES
Table 1: GC-MS of biodiesel from fresh cooking oil ………………………………………………21
Table 2: GC-MS of biodiesel from waste cooking oil……………………………………………..21
Table 3: Infrared spectra of biodiesel from fresh oil………………………………………………..21
Table 4: Infrared spectra of biodiesel from waste cooking oil…………………………………..22
Table 5: Comparison between the produced biodiesel and ASTM standards ……………..23
v
LIST OF FIGURES
Figure 1: Effect of biodiesel use on emissions………………………………………………………….3
Figure 2: Schematic representation of biodiesel production pathway ………………………….4
Figure 3: Effect of ethanol addition to B100 on NOx emission ………………………………….7
Figure 4: effect of 10% Diethyl ether on the CO emissions of B20 fuel blend ……………..8
Figure 5: Effect of 10% on the HC emissions of B20 fuel blend ………………………………..8
Figure 6: Effect of methanol and ethanol addition on the flash point of biodiesel…………9
Figure 7: Effect of Diethyl ether on the density of biodiesel-diesel blendsl………………..10
Figure 8: Effect of ethanol on the density of biodiesel-diesel blends…………………………10
Figure 9: Effect of ethanol on the heating value of B50 fuel…………………………………….11
Figure 10: Effect of Diethyl ether on biodiesel- diesel blend ……………………………………11
Figure 11: Effect of ethanol on the kinematic viscosity of B50 ………………………………..12
Figure 12: Effect of Diethyl ether on the Kinematic viscosity of biodiesel-diesel blends
…………………………………………………………………………………………………………………………12
Figure 13: Effect of Diethyl ether on the pour point of biodiesel-diesel blend ……………13
Figure 14: Effect of ethanol on the pour point of B50 fuel……………………………………….13
Figure 15: Effect of oxygenate addition on the density BDFO …………………………………25
Figure 16: Effect of Oxygenate addition on the density of BDWO……………………………25
Figure 17: Effect of oxygenate addition on the specific gravity of BDFO………………….26
Figure 18: Effect of oxygenate addition on the specific gravity of BDWO ………………..26
Figure 19: Comparison between the kinematic viscosities of fresh and waste oil………..28
Figure 20: Effect of oxygenate addition on the kinematic viscosity of BDFO…………….29
Figure 21: Effect of oxygenate addition on the kinematic viscosity of BDWO …………..30
vi
Figure 22: Effect of oxygenate addition on the heat content of BDFO ………………………32
Figure 23: Effect of Oxygenates on the heat content of BDWO ……………………………….32
vii
LIST OF EQUATIONS
Equation 1: Trans-esterification of vegetable oil………………………………………………………4
Equation 2: Acid Value……………………………………………………………………………………….14
Equation 3: Moisture Content………………………………………………………………………………15
Equation 4: Specific Gravity………………………………………………………………………………..15
Equation 5: Ash Content……………………………………………………………………………………..16
Equation 6: Density…………………………………………………………………………………………….16
Equation 7: Percentage Yield……………………………………………………………………………….17
1
CHAPTER 1: Introduction
The recognition of global warming and depletion of fossil fuels has led to the
search for other energy options which are environmental friendly and sustainable.
Emission of greenhouse gases from fossil fuels has led scientists to turn to biofuels as an
alternative source. Biofuels are fuels made from different types of biomass such as
cellulose, algal oil, corn, soy, sugar cane, jatropha, camelina, rapseed, animal fat,
methane, paper waste and the likes. These sources create different fuels such as
bioalcohols, plant based biodiesel and kerosene, biogas, solid biofuels and the likes
(Webb & Coates, 2012).
1.1 Biodiesel
Biodiesel has grown quite a name for itself since its inception in the 20th century.
It is a liquid biofuel composed of simple alkyl esters of fatty acids made from the transesterification of vegetable oils and animal fats which are renewable and nontoxic. It is
known for its production of low greenhouse gases as compared to fossil fuel (Fangrui &
Milford, 1999). The biodiesel produced is independent of the starting material which
makes any material containing free fatty acids a suitable feedstock (Michael, Andrew,
Winnie, & Thomas , 2006).
Biodiesel production has increased considerably in the last thirty years due to its
properties that confirm it environmentally suitable. It is now being accepted in the
commercial world as several institutions adopt its use such as businesses, governmental
2
organizations, schools and the likes. This trend is expected to continue over the years to
come (Michael, Andrew, Winnie, & Thomas , 2006).
1.2 Advantages of biodiesel
The advantages of biodiesel over conventional diesel have been proven to be
very essential in curbing emissions of carbon dioxide, sulfur oxide, particulate matter,
and polycyclic aromatic hydrocarbons due to the fact that it has 10-11% oxygen by
weight and allows for complete combustion of the fuel (Arjun, Chris, & Rafiqul, 2008).
Its use comes with lower health problems which is possible since it has a reduced
emission of carcinogenic substances. The environment is safer even with biofuel spill
due to its high degradability and low toxicity (Romano & Sorichetti, 2011). Reports
have suggested that the life cycle of carbon dioxide emissions have been cut down to
30% with the use of biodiesel as compared to conventional diesel (Gerard, Bruno,
Dominique, Laurent, & Jean-Alain, 2003). As promising as biodiesel is there are
limitations to it that need improvement.
3
Figure 1: Effect of biodiesel use on emissions (U.S. Department of Energy, 2014)
1.3 Biodiesel production
Biodiesel is synthesized from animal or vegetable fat via trans-esterification. The Fig.
below shows a schematic of the production path involved in the synthesis. During the
trans-esterification process, triglyceride is converted to methyl or ethyl esters with the
aid of an alcohol usually methanol and a base catalyst, potassium hydroxide which is
more efficient than sodium hydroxide. An excess of alcohol drives the reaction towards
the production of methyl or ethyl esters. The equation below shows the mechanism of
conversion involved in the production of biodiesel (Encinar, Gonzalez, Martinez, &
Pardal, 2010).
4
Figure 2: Schematic representation of biodiesel production pathway (U.S. Department of Energy, 2014)
Equation 1: Trans-esterification of vegetable oil (Encinar, Gonzalez, Martinez, & Pardal, 2010)
1.4 Waste vegetable oil as feed stock
The feed stock for biodiesel production is a controversial topic due to the fact
that it takes up food meant to be eaten like using soy, palm kernel, castor oil and the
likes. This causes a debate on which is important, food or fuel? The use of waste
vegetable oil, jatropha and other nonedible oil, producing plants for the production of
biodiesel is a very popular topic most especially waste cooking oil which has virtually
5
no cost in securing it as a feed stock. 70-95% of the cost of producing biodiesel comes
from the feedstock and using waste oil takes care of that cost (Arjun, Chris, & Rafiqul,
2008). The use of waste cooking oil in the production of biodiesel allows for its recycle
seeing as its disposal holds serious damages in public sewers, waste water and even
streams of flowing water (Nor, Sulaiman, & Nurrul, 2013).
1.5 Limitations of Biodiesel
Though biodiesel has promising prospects, in order to be fully accepted as an
alternative to fossil fuel, its properties need to be improved upon such as the cetane
number, energy density, viscosity, flash point and the likes. Modifications of the fuel
properties can enable it to be well matched to that of conventional diesel. There have
been a handful of researches that investigate the effect oxygenates have on biodiesel
most especially the blends with diesel (Imtenan, et al., 2014).
1.6 Aims, Objectives and Significance
Oxygenates with good fuel properties such as ethanol, diethyl ether and methanol
may be efficient in improving the properties or characteristics of biodiesel. The aim of
this study is to investigate the properties of biodiesel produced from fresh cooking and
waste cooking oil blended with oxygenates such as ethanol, methanol and diethyl ether.
This study will create awareness on the modifications that can occur when biodiesel is
blended with oxygenates and this can further help the biodiesel industry to flourish.

DOWNLOAD COMPLETE WORK

DISCLAIMER: All project works, files and documents posted on this website, eProjectTopics.com are the property/copyright of their respective owners. They are for research reference/guidance purposes only and some of the works may be crowd-sourced. Please don’t submit someone’s work as your own to avoid plagiarism and its consequences. Use it as a reference/citation/guidance purpose only and not copy the work word for word (verbatim). The paper should be used as a guide or framework for your own paper. The contents of this paper should be able to help you in generating new ideas and thoughts for your own study. eProjectTopics.com is a repository of research works where works are uploaded for research guidance. Our aim of providing this work is to help you eradicate the stress of going from one school library to another in search of research materials. This is a legal service because all tertiary institutions permit their students to read previous works, projects, books, articles, journals or papers while developing their own works. This is where the need for literature review comes in. “What a good artist understands is that nothing comes from nowhere. The paid subscription on eProjectTopics.com is a means by which the website is maintained to support Open Education. If you see your work posted here by any means, and you want it to be removed/credited, please contact us with the web address link to the work. We will reply to and honour every request. Please notice it may take up to 24 – 48 hours to process your request.

WeCreativez WhatsApp Support
Administrator (Online)
Hello and welcome. I am online and ready to help you via WhatsApp chat. Let me know if you need my assistance.