Page Length: 43

Size: 113 KB

Format: PDF & Word

5,000.00

ABSTRACT

The construction of sieves system was carried out in the Engineering workshop, Institute of management and technology, Enugu.

The aim of this project is to fabricate a sieve system, which is capable of separating solid particles of various sizes.

 

The construction was carried out in order to analyze the sizes of particles.

The component parts of the sets of sieve and their dimension are as follow:

Height of sieve –80mm

Number of sieve –4

Diameter of sieve –230mm

Shape of sieve –cirular

https://rufortouthee.com/4/7692130

Height of sieve set –760mm

Mesh/hole sizes – top –6.0mm, 2nd 5.0mm, 3rd 3.0mm bottom 1.0mm downwards respectively.

In constructing of this sieve system, some factors were taken into consideration and they are:

-the capacity of the sieve

-the type of mixture that can be filtered in it

-the types of properties and decomposition of the mixture.

-the type of material to be used for constructing the sieve.

The cost which is the determinant, factor in fabrication of any equipment.

 

These factors, help greatly in the fulfillment of the objective of this project study.

At the end of the fabrication, a sieve equipment was construct with specified dimension.

 

TABLE OF CONTENT

TITLE PAGE                                                                           II

APPROVAL PAGE                                                                 III

LETTER OF TRANSMITTAL                                                 IV

DEDICATION                                                                        V

ACKNOWLEDGEMENT                                                        VII

ABSTRACT                                                                            VIII

 

CHAPTER ONE
  • INTRODUCTION 1

 

CHAPTER TWO

LITERATURE REVIEW                                                         3

  • HISTORY OF SIEVE 4
  • THEORY OF SIEVE 4
  • SCREENING 6
  • STANDARD SCREEN 7
  • MATERIAL BALANCES OVER SCREEN 9
  • EFFECTIVENESS/EFFICIENCY 10
  • SCREEN ANALYSIS 11
  • TYPES OF SCREENING 14
  • EFFECT OF MESH SIZE ON CAPACITY OF SCREEN17

 

CHAPTER THREE
  • MATERIALS OF CONSTRUCTION 23
  • ANALYSIS OF MATERIAL OF CONSTRUCTION 23
  • MAINTENANCE OF SIEVE COMPONENT 24
  • SAFETY PRECAUTION 24

CHAPTER FOUR

  • FABRICATION PROCEDURE 25
  • LAYOUT 25
  • FABRICATION OF SIEVE PLATE
  • SMOOTHENING AND FILLING 28

 

CHAPTER FIVE

DISCUSSION                                                                         31

 

CHAPTER SIX

CONCLUSION AND RECOMMENDATION                          34

REFERENCE                                                                          36

APPENDIX                                                                             37

 

 

CHAPTER ONE

INTRODUCTION

Generally, all chemical engineering mostly deals with the construction of sieve among others construction in order to fulfill the theory of separations technique. This construction is carried out so as to achieve and put to practice chemical process with the help of some component for equipment construction procedures.

Sieving equipments produces a nice separation of solid particles, although artificially, by allowing the social particles to pass through the pores or the a pasture, which consists of orderly, arrange set of sieves which is arranged in manner with their facilities sizes and shapes.

Sieving equipments operates satisfactory with reasonable coarse and fine particles, so that separation can be done they have high sensitive efficiency, but few have been built since the development of separation of particles, because of the lost and the procedures involved and the labour needed to clean the sieve plate and to handle the sieve equipment.

 

Moreover, in the construction of set of sieve, we have to bear certain qualities in mind to portray such as determination of size and shape of the equipment which contributes to the efficiency of the equipment.

However, the operation has evolved as a particle at rather than a theoretical science, nevertheless, its theory has received steady attention since the pioneering work of some important scientist half a century ago.

They are usually used in large industries like mining, coal, gold, diamond and pharmaceutical etc, because of its importance and efficiency and would not be seen commonly.

Above all, the purpose of this project is to fabricate a set of sieve which sole aim is for separation of solid particles of different size by passing through the mesh with the help of shaking and larger particles retained on the mesh (oversized) and the particles that passes through (undersized) enables us to separate the particles.

DOWNLOAD COMPLETE WORK

DISCLAIMER: All project works, files and documents posted on this website, eProjectTopics.com are the property/copyright of their respective owners. They are for research reference/guidance purposes only and some of the works may be crowd-sourced. Please don’t submit someone’s work as your own to avoid plagiarism and its consequences. Use it as a reference/citation/guidance purpose only and not copy the work word for word (verbatim). The paper should be used as a guide or framework for your own paper. The contents of this paper should be able to help you in generating new ideas and thoughts for your own study. eProjectTopics.com is a repository of research works where works are uploaded for research guidance. Our aim of providing this work is to help you eradicate the stress of going from one school library to another in search of research materials. This is a legal service because all tertiary institutions permit their students to read previous works, projects, books, articles, journals or papers while developing their own works. This is where the need for literature review comes in. “What a good artist understands is that nothing comes from nowhere. The paid subscription on eProjectTopics.com is a means by which the website is maintained to support Open Education. If you see your work posted here by any means, and you want it to be removed/credited, please contact us with the web address link to the work. We will reply to and honour every request. Please notice it may take up to 24 – 48 hours to process your request.

WeCreativez WhatsApp Support
Administrator (Online)
Hello and welcome. I am online and ready to help you via WhatsApp chat. Let me know if you need my assistance.